Whirlpool Stove Fault Codes
F1 – E0 – EEPROM communication error
1. Disconnect the power for at least 30 seconds.
2. Re-apply the power and watch for at least one minute.
3. If the code re-appears, replace the control board (ERC or clock).
Note: Applies to all F1-E… codes except F1-E3.
F1 – E1 – EEPROM checksum error
F1 – E2 – UL A/D error(s)
F1 – E4 – Model ID error
F1 – E5 – Calibration shifted
F1 – E6 – Latch signal mismatch error
F1 – E9 – Stack overflow
F1 – E3 – Wiring harness cavity size does not match previously stored value
The “Cavity Size Select” jumpers inside the wiring harness indicate a cavity size different from that which the control was previously configured for.
Check the jumpers in the harness to ensure that they agree with the actual oven size.
F2 – E0 – Shorted keypad (also called touch pad)
Inspect the keypad connector for firm connection (keypad connects to control board).
Press CANCEL. If the error code returns after 60 seconds, replace the keypad (touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace the control board (ERC or clock).
F2 – E1 – Keypad cable unplugged
F2 – E5 – Cancel key drive line open
F2 – E6 – Cancel key drive line open
F3 – E0 – Oven temperature sensor (RTD) opened (upper oven, if double oven)
Replace the Oven temperature sensor (RTD)
Note: Applies to all F3-E… codes.
Whirlpool Oven Fault Codes
F3 – E1 – Temperature sensor (RTD) shorted (upper oven, if double oven)
F3 – E2 – Oven temperature is too high (Cook mode)
F3 – E3 – Temperature is too high (Clean mode)
F3 – E4 – Oven temperature sensor (RTD) opened (lower oven, if double oven)
F3 – E5 – Temperature sensor (RTD) shorted (lower oven, if double oven)
F3 – E6 – Warming drawer sensor open
F3 – E7 – Drawer sensor shorted
F4 – E1 – Meat probe malfunction – shorted
Problem possibly with the probe, receptacle, or probe circuit. Check the probe. Look for a pinched wire. Look for condensation or contamination on the probe receptacle. Replace the probe if all else checks out ok.
F5 – E0 – Door switches do not agree (condition exists when the door switch is closed indicating an open door, and latch switch is closed indicating a locked door)
F5 – E1 – Self-clean latch will not lock
F5 – E2 – Latch during CLEAN error
F5 – E5 – Self-clean temperature not reached within 45 minutes.
F5 – E6 – Door is open, but latch is locked
F5 – E7 – Self-clean latch will not unlock
F6 – E0 – Return line not connected
If the switch pulse return line is not connected, electronic control will display F6 within 60 seconds after power up. Replace the control.
F7 – E1 – Common switch wire is defective
Wire common (+5VDC) to latch switch, and to door switch is shorted to chassis ground or neutral. A double oven has two of each switch and one common wire.
Check the connections at control and at the latch switch and door switch.
If all the connections are good, then check the individual switches as outlined for the F5 failu
Whirlpool Refrigerator Fault Codes
L01 – The refrigerator temperature sensor is faulty
AL02 – the evaporator temperature sensor is defective
AL03 – the freezer temperature sensor is defective
CF – module does not see the display, there is no communication
EO – Ice maker fault (if fitted)
E1 – Refrigerator sensor fault
E2 – Freezer sensor fault
E3 – Defrost sensor fault
E4 – Fridge defrost sensor fault
E5 – Freezer defrost sensor fault
E6 – Main control board and display board fault
E7 – Environmental temperature sensor fault
E9 -Freezer high temperature alarm
EE – Ice maker circuit fault
Whirlpool Dishwasher Fault Codes
F1 – Problem with the NTC (temperature sensor) or thermistor
F2 – water leak has been detected
F3 – Issue with water heating system
F5 – Spray arms are blocked/clogged or otherwise malfunctioning
F6 – The fault occurs when the dishwasher does not detect any incoming water despite the water inlet valve being open
F7 – Flow meter failure is not unusual on Whirlpool dishwashers so it may well require replacing
F8 – Water Turbidity Fault
F9 – Water inlet is staying open (dishwasher is overfilling)
F0 – Sensor fault or failure
FA – The optical water indicator is detecting high levels of water turbidity
FB – Motorised diverter valve fault detected
FC – Water hardness sensor failure
Whirlpool Washer & Dryer Error Codes
F01 – F30 – Electrical Problem
F01 – No water detected entering machine or pressure switch trip not detected
F02 – Overflow condition
F03 – Long drain
F05 – Water temperature sensor error
F06 – Drive motor tachometer error
F07 – Electronic circuit board fault/ heating circuit fault
F08 – Heater fault
F09 – Software fault
F11 – Pump circuit fault
F12 – Electronic control fault
F22 – Loads detected during clean washer cycle
F23 – Pressure switch error
A09 on display – Water Inlet Problem—no water or insufficient water supply
A10 – Drain Problem
Sd – Excessive suds in washer. Washer is running a suds reduction routine.
Sud – Excessive suds in washer. Washer is running a suds reduction routine.
Fod – “Overfoaming”
Too much foam interrupted the wash program.
Write a Comment