Fault Codes Frigidaire Gallery Appliance Repair
Fault codes are often the result of a bad timer (ERC or Electronic Range Control). In some cases, the failure code indicates another problem when, in fact, the timer is to blame. Fortunately, our team is experienced and trained in resolving timer issues. So, when you notice any of the below fault codes, call our team right away and we will be at your door before you know it! Additionally, you may also find further information about appliances and our services at.
Frigidaire Gallery Refrigerator Error Codes
OP in freezer temperature display – Freezer temperature sensor open
SH in freezer temperature display – Freezer temperature sensor shorted
OP in refrigerator temperature display – Refrigerator temperature sensor open
SH in refrigerator temperature display – Refrigerator temperature sensor shorted
SY EF – Evaporator fan circuit failure
SY CE or SY CF – Communications failure between the electronic control board and user interface
Frigidaire Gallery Oven Error Codes
F0 – Electronic oven control fault
- Replace the electronic oven control ( EOC or clock).
F1 – Electronic oven control fault
- Replace the electronic oven control ( EOC or clock).
F2 – Oven temperature is too hot
- Inspect and replace oven temperature sensor (RTD).
F3 – Oven temperature sensor (RTD) is open
- Inspect the sensor harness and harness connection between the oven sensor and oven control.
- Replace the oven temperature sensor (RTD) if the wiring is intact.
F4 – Oven temperature sensor (RTD) has shorted
- Inspect the sensor harness and harness connection between the oven sensor and oven control. Replace the oven temperature sensor (RTD) if the wiring is ok.
F5 – Electronic oven control fault
- Replace the electronic oven control (also called EOC or clock).
F6 – Electronic oven control fault
- Replace the electronic oven control (also called EOC or clock).
F8 – Oven door lock fault
- Inspect the lock relay and door switches.
Frigidaire Gallery Dishwasher Error Codes
i10 – A low fill has been detected.
i20, i40, iF0 – Clogged filters or a restricted drain line has been detected.
i30 – A leak or over flow of water has been detected in the bottom pan.
i50 – A problem has been detected with the drain or wash motor.
i60 – A problem has been detected with the water heating system.
iC0 –A problem has been detected with the electronic control system.
UO – Vent open
UF – Fan not running
ER – Membrane Switch Failure
CE – Configuration Error
CL – Close Door – Door Switch Open
dP – Drain Pump
FL – Water Valve Is Open
HO – Heat Delay
hs – Hall Sensor
LO – Low Rinse Aid
PF – Power Failure
rA – Rinse Aid
RE – Rinse aid reed switch
RF – Rinse aid
rt – Relay / Triac Test
Sd – Detergent Dispenser
tu –Turbidity Sensor
Frigidaire Gallery Affinity Dryer Error Codes
E10 –Electronic control board communication error
E11 –Electronic control board communication error
E12 –Electronic control board communication error
E24 – Thermistor error
E25– Thermistor error
E4A – Long dry time
E5B – No heat
E68 – Stuck key on the electronic control board
E8C – Frequent high-limit thermostat trips
EAF – Electronic control board failure
Frigidaire Gallery Affinity Washer Error Codes
E11 – Fill time too long
E13 – Water leak in the tub or air leak in the water level pressure sensor air hose
E14 – Dispenser drawer not , closed
E21 – Drains slowly
E23 – Drain pump relay failed
E24 – Drain pump relay failed
E31 – Water level pressure sensor isn’t communicating with the electronic control board
E35– Water-level pressure sensor detects overfill
E43 –Control detects a problem with the door lock circuit
E44 – Control board failure
E45 – Control board failure
E46 – Control board failure
E47 – Control detects an open door lock circuit in Spin mode,
E48 – Control detects a , problem with the door lock circuit
E52 – Signal from the drive motor tachometer
E55 – Motor overheating
E56 – High motor current
E57 – High current on, inverter
E58 – High current on motor phase
E59 – No tachometer signal, for 3 seconds
E5A – Motor control board is overheated,
E5B – Motor control board is overheated
E5C – Motor control board is overheated
E5D – Communication failure between the electronic control board and the motor control board,
E5E – Communication failure between the electronic control board and the motor control board,
E5F – Communication failure between the electronic control board and the motor control board,
E67 – Incorrect voltage supply to the microprocessor on the electronic control board
E75 – Failed water temperature sensor circuit
E95 – Electronic control board communication error,
EB1 – Incoming power , frequency out of limits
EB2 – Incoming line voltage is , above 130 volts AC
EB3 – Incoming line voltage, is below 90 volts AC
EF1 – Clogged drain pump,
EF2 – Too much suds
Write a Comment