Common Fault Codes for KitchenAid
Kitchenaid Dryer Error Codes
PF – Power Failure
E1 – Open Thermistor
E2 – Shorted Thermistor
E3 – User Interface or Software Mismatch
FH – Detects No Water Entering Machine or No Pressure Switch Trip
F02 – Long Drain (Drain Exceeds 8 Minutes)
F05 – Water Temperature Sensor Error
F06 – Drive Motore Tachometer Error
F07 – Motor Control Unit (MCU) Error
F09 – Overflow Condition
F10 – Motor Control Unit (MCU) Heat Sink Thermal Trip (Too Hot)
F11 – Serial Communication Error between MCU and CCU
F13 – Dispenser Circuit Error
F13 – Dispenser Circuit Error
F15 – Motor Control Unit (MCU) Error
F21 / F22 – Central Control Unit (CCU)/ Touch Pad / LEd Assembly Error
F32 – Pressure Switch Failure
F33 – System Leak
FdU – Door Unlock Error
FdL – Door Lock Error
SUD – Suds Lock
Kitchenaid Washer Error Codes
FH – Detects No Water Entering Machine or No Pressure Switch Trip
F02 – Long Drain (Drain Exceeds 8 Minutes)
F05 – Water Temperature Sensor Error
F06 – Drive Motor Tachometer Error
F07 – Motor Control Unit (MCU) Error
F09 – Overflow Condition (Pressure Switch Closed Too Long)
F10 – Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot)
F11 – Serial Communication Error Between MCU and CCU
F13 – Dispenser Circuit Error
F14 – EEPROM Error – Disconnect power and unplug unit.
F15 – Motor Control Unit (MCU) Error
F21 / F22 – Central Control Unit (CCU) / Touch Pad / LED Assembly Error
FdU – Door Unlock Error
FdL – Door Lock Error
SUD – Suds Lock
Kitchenaid Dishwasher Error Codes
1-1 or F1E1– Stuck relay on the electronic control board
1-2 or F1E2 – Damaged or corrupted memory on control board. Incompatible software components inside microprocessor.
2-1 or F2E1 – Stuck button on the user interface control
2-2 or F2E2 – User interface control can’t communicate with electronic control board
3-1 or F3E1– Thermistor/OWI sensor failure
3-2 or F3E2 – Shorted thermistor/OWI sensor
3-3 or F3E3 – OWI failed to calibrate or the drain hose check valve failed, allowing dirty water to backflow into the dishwasher
4-4 or F4E4 – Communication error between the electronic control board and the circulation pump motor
5-1 or F5E1– Door switch failure
5-2 or F5E2– Control detects door not opening
6-1 or F6E1– Won’t fill
6-2 or F6E2– Water inlet valve failure
6-3 or F6E3– Suds or air are in the water pump
6-4 or F6E4– The float switch is open
6-6 or F6E6– Incoming water is too cold
7-1 or F7E1– Heating element doesn’t work
7-2 or F7E2 – Heating element won’t shut off
8-1 or F8E1 – Slow drain
8-2 or F8E2 -Drain pump electrical problem
9-1 or F9E1 – Electronic control board can’t detect the position of the diverter disc
9-2 or F9E2 – Diverter motor is stuck on
9-3 or F9E3 – Diverter disc is missing
9-4 or F9E4 – Lower spray arm error
10-1 or FAE1– Detergent dispenser failure
10-3 or FAE3 -Drying fan failur
Write a Comment