Repair of AEG Appliance in Edmonton

Repair of AEG refrigerators and freezers. The German company ” AEG ” is a brand that has a rich history and belongs to the leaders of the European market of home appliances. The name ” AEG ” stands for Allgemeine  Elektrizitats Gesellschaft. More than 100 years have passed since the company was founded by Emil Rathenau, and over these years a huge experience in the development and creation of home appliances has been gained. The company is developing in many directions and achieving success everywhere. Throughout its history, AEG has put responsibility above all else, selecting employees and training professional staff. Today “AEG” refrigerators and freezers are the most modern equipment and very responsible work of the staff. Our service center is Still working and repairs AEG refrigerators and freezers of the following brands.

Our company provides services in: Sherwood Park, Fort Saskatchewan, Devon, Spruce Grove, Stony Plain, St. Albert, Morinville, Gibbons, West & North & Southside Edmonton, Beaumont ,Leduc.

The AEG washing machine does not turn on

The AEG washing machine does not turn on. If the AEG washing machine suddenly stops working, the tableau does not turn on and the numbers do not show, We will help you. In such cases, the problem arises from the power supply unit. The drum does not rotate. When you click start, the AEG washing machine does not turn on. You need to replace the engine or a defect in the electronic Board, The water does not fill the tank. you need to replace the water valve, after washing the hatch does not open. you need to fix the door lock or replace it. The AEG washing machine does not complete the washing cycle, it stops for half of the washing. The fault may be in the software (firmware) or due to a voltage drop or program failure. Washing machines of this famous company are valued not only in Europe but also around the world. Assembly is carried out in accordance with international standards and all norms are observed. Unfortunately, nothing lasts forever and in rare cases, there may still be a breakdown of these washing machines due to improper detergents, the ten fails, the pump and water gets into the bearing.

Does not drain water washing machine Aeg

The AEG washing machine does not drain water. If the tableau (display) shows an error washing machine Aeg, it Means there is a breakdown. All the mistakes of washing machines show that it is broken. The manufacturer of this brand passed these errors to the processor so that the master could quickly determine the failure. Repairs in any case can not be carried out independently, and you need to trust professionals. Service center “GoTech Appliance Repairs ” repairs AEG washing machines of any complexity, and all work is carried out in the shortest possible time. Do not forget that carrying out repairs yourself can lead to loss of warranty and operability of the washing machine.

AEG washing machine malfunctions

AEG washing machine diagram Malfunctions of AEG washing machines. Troubleshooting and Troubleshooting AEG washing machines in your city in Edmonton. Not included washing machine indicator is not lit. One of the reasons may be the power unit, the power supply failed. We repair the control unit modules of the washing machine of all types and models of the company Aeg. Our specialists will repair the power supply of washing machines at the element level. The AEG washing machine does not turn the drum. The defect may be in the engine or you need to replace the brushes. The washing machine does not heat the water. A fault in the heating element, the fuel tank Burned out. When enabled, the main PATTERN is eliminated. There is a short circuit in the washing machine and you Need to diagnose it. The AEG washing machine does not drain water. Replacement of the drain pump or need to carry out major repairs cleaning the system. Our service Technicians are ready to repair your washing machine on site at your home.

AEG washing machine error code

AEG washing machine error codes. E11-the AEG Washing machine does not collect water, which means: the tank was not filled with enough water in the time allotted to it. The machine shows E11 on the display due to such failures. 1. The failure of the filler valve or the schema management module. 2. Broken coil valve. The AEG washing machine displays the error code E13 indicating a water leak. As a rule, the leak occurs in the AQUASTOP pallet. You need to check the machine for leaks.

On the screen of the AEG washing machine, the error code E21-24 POPs up – the Machine did not drain the waste water for 10 minutes. The pump broke. Using a tester, check the winding: if the pump is correct, the indicator will be in 170 Ohms. The E23 code appears when the control triac on the control unit is broken. To reset errors, check that the specified element is working correctly. If it fails, replace it. You may need to change the entire control unit. The E24 code Means that the circuit between the control triac and the drainage pump is broken. What should I do to fix the problem? First, you need to check all the nodes of the chain for serviceability. E31-level sensor Failure. E32-what does E32 mean? After initial calibration, the water level exceeds the mark. Ensure the water supply by opening the water valve. The E33 Code reports three reasons for this failure. Blockages in the level sensor connections. Blockage in the pressure sampling chamber of these elements. E34-the coordinated operation of the pressostat and level circuit is Disrupted. E35-Indicates that the tank is full of water. E36-the protection level sensor of the tubular heater (tena) is Broken. E38-the pressure Difference is not fixed. Reason: clogging of the nozzle.On the washing machine Aeg shows the error code

E39-fixing the overflow of water into the tank. E3A-Code indicates that the Heater relay is broken or the heating element is broken. E41-Close the door more tightly to reset the error. You may need to repair the guide rail.

In case of error E42, you need to check the device that blocks the hatch in case of failure, replace it with a new one. E43-indicates a failure of the control triac. E44-Failure of the sensor for closing the hatch door. E45-it is possible to diagnose a failure of elements in the circuit between the control triac and the door lock. E51-short circuit in the engine. E52 – problem in the Tacho generator. E53-motor triac control. E54-the verbal contact group does not work. If the AEG washing machine shows the error code E55 – breakage in the engine. E58-the motor uses a large current. E59-Check the Tacho generator and replace it with a new one. E62-If the AEG washing machine shows error 62, it means that the temperature sensor-thermistor could have failed. You can check its performance using the tester. The resistance at room temperature should be within 5.7-6.3 kom.

What does the code error E66 mean – failure of the relay of the tubular electric heater. E68 – high current on a heating element or in another circuit. CD-the hatch is not closed. CF-memory failure. C9-Tacho sensor Failure. C8-thermistor Failure. C7-ten burned or shorted to the body. C6 pressure switch Failure. C5-engine Overheating. C4-failure of the drainage pump. C1-Water does not enter the tank. C0-level sensor Failure. EN series breakdowns codes (1, 2, 3,). Basically, these codes are lit on the tableau when there are failures in the electronics. EF5-the spin was Interrupted. A large imbalance was diagnosed (more than 1.2 kg). EF3-the “Aqua Control” system was Activated. EF1-the System detected blockages in the water drain filter or drain hose. EC1 fill valve Lock. E 94-indicates an error in the configuration of the eraser and the program cycle. Codes E82 – E85 in AEG erasers – module failure. E71-the resistance Of the thermal sensor has exceeded the allowed range.

Repair of AEG glass ceramic stoves in Edmonton

Repair of AEG glass-ceramic stoves in Edmonton. The cooktops of this famous AEG brand are valued not only in Europe but all over the world. Assembly is carried out in accordance with international standards and all SCHOTT CERAN standards are observed. Everyone knows that glass-ceramic dependent and independent plates can break when working. this can lead to a jump in the voltage in the network or a drop in electricity in the outlet, even a weak contact in the input pad. Unfortunately, nothing lasts forever and in rare cases, these cooktops can still break down. If the built-in AEG panel has stopped working and the sensor does not respond to button clicks, then there is already a defect in the block. Repair of AEG glass-ceramic plates. Our masters will repair your stove efficiently and quickly.

Repair of Cook top AEG errors

Repair of AEG Cook Top. To repair AEG sensor built-in stoves, you need to know that each cooking surface (ceramic stove) of this brand AEG has its own error. Each error code means that the module is faulty. The manufacturer has flashed the program for errors in the processor Err-error, E, F. on the surface panel Aeg code error F1 heated control module. On the display of the AEG touch plate, the program has failed. the hob beeps and gives the error F3 there is no connection between the two boards. error F4 wait for the burners to cool down or the software to fail. Error F5 power failure in the power control module. Error F6 indicates there is no connection to the power inverter. the AEG ceramic plate clicks the numbers flicker and turns off. error F8 there is not enough power in the power unit. E8 loss of communication between two blocks. F9 module fault. ER 22 several buttons are pressed. Call a specialist and your district master will come to you.

The AEG Stove not work malfunctions

The AEG Stove not work. Problems and causes! The sensor does not work, the AEG panel does not turn on – the problem may be in the power supply unit or a processor failure. The numbers are lit on the display and the left or right burner does not turn on – the problem is in the power unit, does not turn on the relay or does not receive a signal from the processor. One circle is not switched off (expansion of the burner) the failure may be in the burner itself or in the power unit, the voltage stabilizer does not work correctly. The numbers on the screen flicker and you can hear strange sounds (beeps) – the voltage stabilizer is out of order. If the hob suddenly turns off and stops working? Our specialists will cope with these problems. The service center “Everything works” is ready to diagnose and solve all your problems.

Repair of AEG induction cookers in Edmonton

Repair of AEG induction cook top in Edmonton. Does not turn on the induction cooker, one burner? The AEG induction hob does not see the dishes. One of the reasons may be the control module of the power unit. When the AEG hob is turned on, the main RCD machine is eliminated. This means that the AEG plate has a short circuit. Repair in any case can not be carried out independently! People sometimes search the Internet for a forum on repairing cooktops, how to repair the AEG control module and get the answer replace the control module. You just need to trust the professionals. Service center “GoTech Appliance repairs” will repair your AEG hob, of any complexity, and all the work is carried out in the shortest possible time. Do not forget that performing repairs yourself may lead to loss of warranty.

Replacing the AEG Stove

Replacing the hotplate on AEG cooktops in your area of Edmonton for all AEG ceramic hob models. Cooking rings for the hob are different, two zone, three zone, halogen and spiral burners. Frequently asked questions: How much does it cost to replace the hotplate on AEG ceramic touch plate? The price of an Aeg hob depends on the manufacturer-the diameter of the hob and how many heating elements are in this hob. If one or two circles on the hotplate stop working, it is not a fact that the hotplate has burned down. One of the reasons may be the power module for the control of the cooking zone on the AEG ceramic plate. If the stove has a touch button to activate the second zone of the burner, the defect may be in the electronic module. The three zone burners have a small circle a medium circle for expanding the heating and a large circle. The smallest heating element often fails. To determine the defect that is broken, you need to make a diagnosis. After diagnostics the master will be able to determine whether you need to replace the burner or the burner still broke Our specialists in your area of Edmonton will quickly and efficiently replace the burners for the AEG hob of all types from the manufacturer E. G. O.

Repair of AEG built-in ovens in Edmonton

Repair of built-in AEG ovens. The ovens of this famous company are dependent ovens and independent ones. the AEG brand is valued not only in Europe but also around the world. Assembly of spare parts is carried out in accordance with international standards and all norms are observed. Unfortunately, nothing lasts forever, and in rare cases, AEG equipment may still break down. repair yourself is not recommended, You can complicate the process of fixing the specialist. The oven display does not turn on, the numbers do not light or flicker. You need to repair the clock mechanism (timer). The oven does not work the sensor does not respond to button presses. Problem in the power module, the power Board (power supply) has burned. Look for a service where you can repair the oven. To do this, you need to trust the service center Everything works where your AEG oven will be faithfully repaired.

Malfunctions errors of AEG ovens

Malfunctions of AEG oven errors. The light bulb is working and the stove is not heating? If the AEG server suddenly turns off and stops working, you should never do it yourself, and you need to trust professionals. Does not heat the upper or lower ten. One of the reasons may be the mode switch. Poorly warms the oven, does not keep the temperature. the thermostat is broken or the AEG thermostat is burned out. The service center “GoTech Appliance repairs ” carries out repairs of built-in AEG ovens, of any complexity, and all work is carried out in the shortest possible time. Do not forget that performing repairs yourself may result in the loss of the AEG warranty. Call order a specialist and your district Technition will come to you.

Oven Aeg repair with microwave function in Edmonton

Repair of AEG ovens with microwave function. When switching on the microwave oven, Aeg knocks out the main machine. This indicates that the stove has a short circuit. The plate doesn’t rotate. A fault in the engine torque of the pan. When you turn on the microwave, Aeg turns off after a few seconds. Defect in the inverter power unit. When working with a microwave oven, Aeg sparks and produces strange sounds. The cause of the magnetron malfunction or the protective mica of the microwave has burned. The light bulb is on, but the AEG microwave doesn’t heat it. The fault may be in the transformer or the magnetron needs to be replaced. On pressing the start button) the sensor does not respond and the AEG microwave oven does not turn on. Failure in the control module, burned power Board (power supply). When you turn on the microwave function resets, it means that there is an error in the oven. All errors for each model, the manufacturer stitches a program into the processor so that the master can determine what exactly broke down in the oven.

Replacement of AEG oven switch

Replacing the AEG oven switch. Switches for the AEG oven are of several types, they differ in their function. Six positions or more. Connection modes of heating elements in the oven upper ten lower ten and rear ten for convection oven Aeg. Replacing the switch for the AEG oven is more than seven positions and reaches up to 11 positions. If you have an oven with a grill, you can replace the mode switch with the newest one and you will need to connect the wires correctly so that the switching modes of the upper and lower heating element match the pictures. When you turn on the oven knocks out the main machine. This means that the switch has a short circuit in the contacts or the fuel tank has burned out. You need to restore the contacts of the switch or replace the ten.

Repair of independent AEG ovens

Repair of independent AEG ovens. AEG electric stove is broken and does not give steam. The reason may be in the steam generator. Looking for a service where you can repair an electric stove? When you turn on the AEG oven, the main RCD machine is eliminated. There is a short circuit in the oven. If you suddenly find a breakdown in the oven, you do not need to search the Internet for a forum on repairing built-in AEG ovens. We will help you. Techition for repairing built-in dependent and independent AEG ovens at home. Replacing the heating element in the oven, replacing the temperature sensor (thermostat), fixing the AEG control module, fixing the clock mechanism (timer) for the oven. All questions and answers about repairing AEG ovens can be clarified with the master or with the dispatcher.

Replacing AEG oven glass

Replacement of AEG oven glass. Questions are often asked whether it is possible to change the glass of AEG ovens? To replace the glass on the oven, the first thing you need to say is the model article number. If the stock does not have a price for this model, you need to order. We manufacture glass for AEG ovens and ovens. If you do not find the article number of the oven, our specialist will come on the spot to measure the size of the glass and order for these sizes. Some ovens have two or three panes, the inner middle outer glass of the oven. Frequently asked questions: How much does it cost to replace the glass in the oven? It all depends on the thickness of the size and there is a picture on the glass. Some panes on the oven have a hole for the handle. You need to measure the distance between the hole to then install the handle. To do this, you need to call a specialist at home to accurately measure the size of the glass oven Aeg

AEG electric cooker in Edmonton does not work

The AEG electric stove does not work. The company is particularly popular due to the production of electric kitchen stoves, which are valued by many European families for their ease of use and high level of safety. However, there are cases when the electric stove stops working at all or works incorrectly, for example, slowly heats up. Common are the following types of failures of electric plates: the Failure of the burner; a permanent automatic shut-off plate when you turn on the burners; problems in the operation of the residual heat indicator.

Repair of AEG electric stoves in Edmonton

Repair of AEG electric stoves in Edmonton. Does not turn on the left or right one burner? When enabled, the main PATTERN is eliminated. If you notice any malfunctions in the operation of your kitchen stove, you do not need to search the Internet for AEG kitchen stove repair forum. You need to contact the service center in order to repair the AEG electric stoves in time. One circle (extension) of the hotplate is not disabled. If you want to reduce your time and money, you can contact our service center “GoTech Appliance repairs” Our highly qualified specialists can easily repair AEG electric stoves, thereby identifying and eliminating existing problems. Call a specialist and your district master will come to you.

Replacing the glass on the oven AEG electric stoves

Questions are often asked whether it is possible to change the glass of AEG ovens? To replace the glass on the oven, the first thing you need to say is the model article number. If the stock does not have a price for this model, you need to order. We manufacture glass for AEG ovens and ovens. If you do not find the article number of the oven, our specialist will come on the spot to measure the size of the glass and order for these sizes. Some ovens have two or three panes, the inner middle outer glass of the oven. Frequently asked questions: How much does it cost to replace the glass in the oven? It all depends on the thickness of the size and there is a picture on the glass. Some panes on the oven have a hole for the handle. You need to measure the distance between the hole to then install the handle. To do this, you need to call a specialist at home to accurately measure the size of the glass oven Aeg

Repair of AEG glass-ceramic stoves at home.

Repair of AEG glass-ceramic stoves at home. Is the electric glass-ceramic stove broken? Looking for a service to repair AEG dependent plates? You are at the address. Repair master of AEG glass-ceramic electric stoves. Replacement of the burner for AEG glass-ceramic stoves, replacement of the burner mode switches, repair of the AEG electric timer, replacement of heating elements (ten) for the AEG oven. Repairs are carried out at your home! all questions and answers about repair of electric stoves AEG can specify with the master or with the dispatcher.

Replacing the AEG hotplate

Replacement of AEG electric stoves in your area of Edmonton for all models of AEG ceramic stoves. Hotplates for electric stoves panels are different, two-zone, three-zone, halogen and spiral burners. Frequently asked questions: How much does it cost to replace the hotplate on AEG ceramic touch plate? The price of a hotplate for AEG electric stoves depends on the manufacturer – the diameter of the hotplate and how many heating elements are in this hotplate. If one or two circles on the hotplate stop working, it is not a fact that the hotplate has burned down. One of the reasons may be the power module for the control of the cooking zone on the AEG ceramic plate. If the stove has a touch button to activate the second zone of the burner, the defect may be in the electronic module. The three zone burners have a small circle a medium circle for expanding the heating and a large circle. The smallest heating element often fails. To determine the defect that is broken, you need to make a diagnosis. After diagnostics the master will be able to determine whether the burner needs to be replaced or the burner has broken down Our specialists in your area of Edmonton will quickly and efficiently replace the burners of standing electric stoves AEG of all types from the manufacturer E. G. O.

Replacing the switch on the AEG electric stove

Replacing the switch on the AEG electric stove. Switches for AEG electric stoves are different: one-position, three-position, six-position and more. Connecting the burners of these switches are different. Replacing the switch for the oven in the AEG electric cooker is more than seven positions and reaches up to 11 positions. If you have an old-style stove, you can replace the mode switch with the newest one and you will need to connect the wires correctly so that there is no short circuit. When you turn on the burner knocks out the main machine. This means that the switch has a short circuit in the contacts. You need to restore the switch contacts or replace them with a new one.

AEG refrigerator repair in Edmonton

Repair of AEG refrigerators. refrigerators of this famous company are valued not only in Europe but also around the world. Assembly is carried out in accordance with international standards and all norms are observed. Unfortunately, nothing lasts forever, and in rare cases, AEG refrigerators can still break down. if the AEG refrigerator or freezer is still broken, the passport data shows the model of the refrigerator, the article number, and the refrigerant with which the AEG refrigerator is filled.

Repair of AEG freezers in Edmonton

Repair of AEG freezers. Repair in any case can not be carried out independently, your actions can bring down the factory settings of the AEG refrigerator. Service center “GoTech Appliance Repairs ” repairs refrigerators freezers and wine cabinets aeg, of any complexity, and all work is carried out in the shortest possible time. Do not forget that performing repairs yourself may lead to loss of warranty.

AEG refrigerator failures

Malfunctions of AEG refrigerators and freezers. The refrigerator does not turn on and the indicator does not light. One of the reasons may be the thermostat. The AEG refrigerator or freezer does not switch off. The problem may be thermostat or leaking freon, you need to fill the fridge. The freezer works and the refrigerator does not freeze. The defect may be in the thermal guard. The freezer is constantly running and does not turn off. Failure may be in the refrigerant, lack of freon. Refilling of refrigerators and freezers is carried out at your home. If the refrigerator suddenly stops working, you need to call a specialist to fix the defects. We will help you! Do not search the Internet for a forum on repairing AEG refrigerators. Leave it to the professionals.

AEG Dishwasher repair at home

The Dishwasher Aeg is broken and does not respond to touch buttons. There is a defect in the power Board, the power supply unit has burned out. If you still have a breakdown with the Dishwasher, you can not disassemble and try to repair the Dishwasher Aeg with your own hands. Your actions may violate the factory settings of Dishwasher Aeg. Do not search the Internet for a forum on repairing Dishwasher Aeg. It is important to know if your Dishwasher is dependent, this means that the Dishwasher manages the surface. If one left or right button suddenly stops working, we are ready to help you. Master for repairing embedded dependent and independent Dishwashers at home. Repair of the AEG control module, the touch unit of the electronic Dishwasher , repair of the AEG power unit. All questions and answers about the repair of Dishwasher Aeg can be clarified with the master or with the dispatcher.